Emerson Epsilon EP Drive 400518-01 Manual de instalación Pagina 144
- Pagina / 240
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
132
Epsilon EP-P Drive and FM-3/4 Module Reference Manual
Drive Input Raw
DriveInput.#.Raw
This displays the raw state of the digital input without debounce or forcing to override the raw status.
Drive Input Status
DriveInput.#.Status
This source is the state of the input after debounce and forcing are taken into account.
Drive Output Force
DriveOutput.#.Force
A drive output can be forced either On or Off with this parameter. If the ForceEnable bit is activated, the DriveOutput.#.State
will be set to this value.
Drive Output Force Enable
DriveOutput.#.ForceEnable
If DriveOutput.#.ForceEnable parameter is activated, then the state of the DriveOutput.#.Force bit will override the current
output state.
Drive Output Name
DriveOutput.#.Name
This is a text string up to 12 characters that can be assigned to a given output. It allows the user to use application specific
terminology in naming digital outputs.
Drive Output State
DriveOutput.#State
This destination sets the current state of an output line.
Drive Output Encoder Scaling
DriveOutputEncoder.Scaling
This parameter allows scaling of the drive encoder output resolution in increments of one line per revolution. Allowable range
is from one line per revolution up to the actual density of the encoder in the motor. If the Encoder output scaling is set greater
than the motor encoder density the output scaling will be equal to the motor encoder density.
Drive Output Encoder Scaling Enable
DriveOutputEncoder.ScalingEnable
When on, this parameter enables the use of the drive encoder output scaling feature.
Drive Serial Number
DriveSerialNumber
This displays the serial number of the Drive to which the FM-4 module is attached.
Active Fault
Fault.#.Active
The specified fault is active. See the help index for more information on faults and recovery from them.
- Epsilon EP-P Drive and 1
- FM-3/4 Modules 1
- Reference Manual 3
- Customer Support 5
- Document Conventions 6
- Safety Instructions 7
- Reference Materials 7
- Safety Considerations 9
- Table of Contents 11
- Introduction 13
- Programming Module 14
- Operational Overview 15
- Transmit Cntr 17
- How Motion Works 18
- How Jogging Works 18
- How Home Works 18
- Home Sequence 19
- Sensor then Marker 20
- Accuracy and Repeatability 20
- Home Offset 21
- Calculated 22
- Specified 22
- End of Home Position 23
- Home Limit Distance 23
- Home Examples 23
- Offset Move 24
- How Indexes Work 25
- Absolute vs. Incremental 26
- Absolute Indexes 26
- Absolute Index 27
- Incremental Index 28
- Start Position = 1 Rev 28
- Index Distance = 2 Revs 28
- How Communications Work 29
- Downloading 30
- Change Path Connection 31
- Uploading 32
- Updating to RAM 33
- Communications Tab 34
- PopUps Tab 34
- Secure Downloading 35
- Brake Operation 36
- How Data Capture Works 37
- Setting Up Parameters 39
- Timing Group 40
- Data Group 40
- Setup View 41
- Configuration Group 42
- Drive Encoder Output Group 42
- Positive Direction Group 42
- Update Rate Group 43
- Switching Frequency Group 43
- Motor Position Group 43
- Motor Velocity Group 44
- Control Loop Group 44
- Master Feedback Group 44
- Information Tab (Online Only) 45
- Motor Type List Box 46
- Motor Parameters Column 47
- Values from Drive Column 48
- Apply to Config. Button 48
- Run Auto-Tune Button 49
- Save .ddf Values Button 50
- Existing Motor Names List Box 51
- Velocity Group 53
- Encoder Setup Group 55
- Master Position Setup Group 56
- Master Distance Units 56
- Master Velocity Units 56
- Master Acceleration Units 56
- Master Position Filter 56
- Settings Group 58
- Limits Group 58
- Rotary Group 59
- Online Tab (not shown) 59
- = Index 0 63
- = Index 1 63
- Faults View 66
- Active Faults Group 68
- Power Up Group 68
- Fault Log Tab 68
- Fault Counts Tab 69
- PLS View 70
- Number of PLS Points 71
- ON Point 71
- OFF Point 71
- Setup NVM View 72
- Capture View 73
- Captured Data 74
- Queues View 76
- Full Level 77
- User Variables View 78
- User Bits View 79
- Adding and Deleting User Bits 80
- I/O Setup Group 82
- Assignments 82
- Assignments View 83
- Assignment Polarity 84
- User Level 85
- Only Show Assigned Check Box 85
- Selector View 86
- Input Lines View 88
- Output Lines View 89
- Analog Inputs View 89
- Enable Channel Check Box 90
- User Units 90
- Module Variable 90
- Analog Outputs View 91
- Motion Group 93
- Jog Sources and Destinations 94
- Home View 96
- Home Sources and Destinations 98
- Index View 99
- Timed Indexes 100
- Enable Index PLS 102
- PLS On Point 102
- PLS Off Point 102
- Registration Parameters 103
- Destinations 104
- Adding and Deleting Indexes 105
- Gearing View 106
- Multiple Profiles 107
- Stopping Motion 109
- Network Group 110
- Modbus View 110
- 0xxxx Read/Write Coil bit 111
- DeviceNet View 112
- Profibus View 112
- Ethernet View 112
- Programming 113
- Programs 115
- Program Instruction Types 115
- For Count/Next 116
- Do While/Loop 116
- Wait For 117
- Wait For Time 117
- Call Program 118
- Program Math Functions 120
- Motion Instructions 120
- Dwell for Master Dist 121
- IndexInitiate by Expression: 121
- Complex Velocity Profile 122
- Home.Initiate 124
- Jog.Stop 124
- Jog.PlusInitiate 124
- Jog.MinusInitiate 124
- Motion Modifiers 125
- Using Capture 126
- Using Last 126
- On Profile 126
- Adding and Deleting Programs 127
- Program Multi-Tasking 129
- Program Blocking 130
- Index.0.Initiate 131
- ModuleOutput.1=ON 131
- Example Programs 132
- ‘Dist=50.000,Vel=1.000in/in 133
- Flying Cutoff/Shear 134
- Sequence Learn and Playback 136
- Playback Program (Program 2) 137
- Parameter Descriptions 139
- Home.#.CalculatedOffset 150
- Home.#.SpecifiedOffset 152
- Index.#.RegistrationOffset 155
- Basic Setup Steps 173
- E Series Only 174
- Motor View 174
- User Units View 174
- Master Units View 175
- Position View 175
- Velocity View 176
- Ramps View 176
- Torque View 176
- Tuning View 176
- Step 3: Making Assignments 177
- Drag and 178
- Drop Method 178
- Jog Setup 179
- Home Setup 179
- Index Setup 180
- Step 5: Creating a Program 182
- Software Travel Limits 184
- Home Prox 184
- Making Assignments 185
- Tuning Procedures 191
- Tuning Steps 192
- General Tuning Hints 192
- Tuning Parameters 194
- Feedforwards 195
- Low Pass Filter Group 195
- Line Voltage (EN Only) 195
- RPM - RPM 196
- FV )100(= 196
- Determining Inertia Ratio 197
- Ramp Units Conversion 198
- Diagnostic Display 201
- Fault Codes 202
- Fault Descriptions 203
- Error Messages 206
- Drive Faults 206
- Programming Error Messages 207
- Online Status Indicators 209
- Global Where Am I Button 211
- Motion Status 211
- Channel #2 212
- Analog GND 212
- MDS Dri ve Module 212
- EN Dri ve 212
- Specifications 213
- Cable Diagrams 216
- SNCE-XXX Cable 217
- SNCDD-001.5 Cable 217
- SNCO-003 Cable 218
- TIA-XXX Cable 224
- DDS-XXX Cable 224
- TERM-H (Head) Terminator 225
- TERM-T (Tail) Terminator 225
- CMDS-XXX Cable 226
- CMMS-XXX Cable 226
- CFCS-XXX Cable 227
- CFCO-XXX Cable 228
- CFOS-XXX Cable 229
- Glossary 231
Relacionado con productos y manuales para Software Emerson Epsilon EP Drive 400518-01
Software Emerson Vission Manual de servicio
(148 paginas)
(148 paginas)
Software Emerson Site Manager Guía de instalación
(40 paginas)
(40 paginas)
Software Emerson Vission Especificaciones
(14 paginas)
(14 paginas)
Software Emerson Site Manager Manual de usuario
(130 paginas)
(130 paginas)
Software Emerson Site Manager Guía de instalación
(130 paginas)
(130 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales