Reference Manual
00809-0200-4801, Rev CA
July 2010
A-11
Rosemount 3051S
L_TYPE 16 Direct
Indirect
Indirect Square Root
None Direct Read and Write Linearization type. Determines whether the field
value is used directly (Direct), is converted linearly
(Indirect), or is converted with the square root
(Indirect Square Root).
LO_ALM 35 Not applicable None Not applicable Read only The LO alarm data, which includes a value of the
alarm, a timestamp of occurrence and the state of
the alarm.
LO_LIM 30 Out_Scale
(2)
Out_Scale
(2)
Not applicable Read and Write The setting for the alarm limit used to detect the
LO alarm condition.
LO_LO_ALM 36 Not applicable None Not applicable Read only The LO LO alarm data, which includes a value of
the alarm, a timestamp of occurrence and the
state of the alarm.
LO_LO_LIM 32 Out_Scale
(2)
Out_Scale
(2)
Not applicable Read and Write The setting for the alarm limit used to detect the
LO LO alarm condition.
LO_LO_PRI 31 0 – 15 None 1 Read and Write The priority of the LO LO alarm.
LO_PRI 29 0 – 15 None 1 Read and Write The priority of the LO alarm.
LOW_CUT 17 > = 0 Out_Scale
(2)
0 Read and Write If percentage value of transducer input fails below
this, PV = 0.
MODE_BLK 05 Auto
Manual
Out of Service
None Not applicable Read and Write The actual, target, permitted, and normal modes
of the block.
Target: The mode to “go to”
Actual: The mode the “block is currently in”
Permitted: Allowed modes that target may take on
Normal: Most common mode for target
OUT 08 Out_Scale
(2)
± 10% Out_Scale
(2)
Not applicable Read and Write The block output value and status.
OUT_D 37 Discrete_State 1 – 16 None Disabled Read and Write Discrete output to indicate a selected alarm
condition.
OUT_SCALE 11 Any output range All available none Read and Write The high and low scale values, engineering units
code, and number of digits to the right of the
decimal point associated with OUT.
PV 07 Not applicable Out_Scale
(2)
Not applicable Read only The process variable used in block execution.
PV_FTIME 18 > = 0 Seconds 0 Read and Write The time constant of the first-order PV filter. It is
the time required for a 63% change in the IN
value.
SIMULATE 09 Not applicable None Disable Read and Write A group of data that contains the current
transducer value and status, the simulated
transducer value and status, and the
enable/disable bit.
ST_REV 01 Not applicable None 0 Read only The revision level of the static data associated
with the function block. The revision value will be
incremented each time a static parameter value in
the block is changed.
STATUS_OPTS 14 Propagate fault forward
Uncertain if Limited
Bad if Limited
Uncertain if Man Mode
0 Read and Write
STDDEV 39 0 – 100 Percent 0 Read and Write The average absolute error between the PV and
its previous mean value over that evaluation time
defined by VAR_SCAN.
STRATEGY 03 0 – 65535 None 0 Read and Write The strategy field can be used to identify grouping
of blocks. This data is not checked or processed
by the block.
Parameter
Index
No.
Available Values Units Default Read/Write Description
(16 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales