Emerson X-web300 Manual de usuario Pagina 86
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
Pg.86/106
ACF6
• The total number of compressor of the 2 circuits ( CF04 + CF05 ) is:
√ > 6
√ > 4 with no direct compressor start-up (CO10 ≠ 0) or the number of steps is ≠ 0
(CF06),
√ > 2 and the intermittent valve is configurated with ON (CO08) and OFF (CO09 ) ≠ 0
• Pump-down function but at least in one circuit
√ The pump-down solenoid relay is not present
√ No pump-down pressure switch or evaporating probe when
the pump-down is enabled with unit in start
Or
No low pressure switch configurated.
• The compressor configuration with CF04 and CF05 but not the relay outputs:
√ Main
√ Intermittent valve when enabled with the ON / OFF time, CO08 / CO09 ≠ 0
√ When the by-pass time ≠ 0 and there is no partialization or by-pass valve
configured
√ Motor part_2 / centre of the star with part-winding or star-delta
√ The necessary step valve configurated
• One relay is configured
√ Too much compressors
√ Intermittent valve when ON / OFF time CO08 / CO09 ≠ 0
√ By-pass gas when the by-pass = 0
√ Compressor Motor coil 2 / center of the star with direct compressor start-up
• Too much step valve
ACF7
Evaporator pump
√ Enabled (CO16 ≠ 0) but the relay is not configured
√ Not enabled (CO16 = 0) but the relay is configured
Condenser pump
√ Enabled (CO21 ≠ 0) but the relay is not configured
√ Not enabled (CO21 = 0) but the relay is configured
ACF8
• Thermoregulation probe
9 The thermoregulation probe (in chiller with ST09, in heat pump when enabled with ST10)
is not properly configurated (it does not exist or it is not a NTC)
ACF9
• Recovery cycle enabled Par. rC01 ≠ 0
9 only some of these resources are configured: condensing probe, recovery digital input,
recovery relay, or no outputd is configured.
Causa attivazione Programmazione errata
Reset Programmazione corretta
Riarmo Automatico
Icona
lampeggiante
Azione Relè allarme + buzzer attivato
41.11 ARTF CLOCK FAILURE
Label o the display ArtF (clock failure)
Origin Clock chip failure
Reset Change clock chipset
Restart Manual in function menu
Icona
Blinking
Action Alarm relay + buzzer ON
Regulation
Loads Not changed
Energy saving Disabled if based on RTC
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Comentarios a estos manuales
Relacionado con productos y manuales para Redes Emerson X-web300
Redes Emerson MONITORING OpenComms Manual de usuario
(48 paginas)
(48 paginas)
Redes Emerson OpenComms-485 Manual de usuario
(42 paginas)
(42 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(32 paginas)
(32 paginas)
Redes Emerson X-web500 Manual de usuario
(118 paginas)
(118 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(56 paginas)
(56 paginas)
Redes Emerson Liebert ICOM-DO Manual de usuario
(172 paginas)
(172 paginas)
(166 paginas)
Redes Emerson FM-3 Especificaciones
(110 paginas)
(110 paginas)
Redes Emerson FM-3 Manual de usuario
(8 paginas)
(8 paginas)
Redes Emerson Liebert ICOM-DO Manual de usuario
(12 paginas)
(12 paginas)
Redes Emerson Liebert CW Manual de usuario
(136 paginas)
(136 paginas)
Redes Emerson Liebert FPC Manual de usuario
(58 paginas)
(58 paginas)
Redes Emerson FM-3 Guía de usuario
(263 paginas)
(263 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med