Emerson X-web300 Manual de usuario Pagina 74
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
Pg.74/106
36 LOAD MAINTENANCE
PARAMETERS CO26..CO31 are the set of the running hour counters of the compressors.
They establish, for each load, the number of running hours limit to display a maintenance message.
If one of these parameters is equal to 0 the maintenance signalling is disabled but the running hours counter remains active.
36.1 COMPRESSOR MAINTENANCE RESQUESTS
Label description
ACP1 (maintenance comp. 1) –…ACP6 (maintenance comp. 6)
Activation Compressor running hours > counter setpoint for that compressor
Reset Running hour reset (Hour label in Menu function)
Restart Manual
Icon
blinking
Actions Alarm relay and buzzer activated
REGULATIONS
Actions Only signalling
Loads Not modified
The parameters CO32 / CO33 define the hour set counters for the evaporator water pump / Support
evaporator water pump / Supply fan.
They establish the load running hours limit of the pump/s or the supply fan to give a maintenance signalling. If one of these parameters
is equal to 0 the maintenance signalling of that load is disabled but the running hours counter remains active.
37 CONDENSER FAN REGULATION
The FA01 and FA02 parameters define the operative mode of the condenser fans. The CF68 and CF69 selects which are the output
signals.
Par. CF68 Condenser fan control signal of the circuit #1
0= 0 ÷10V
1= 4÷20mA
2= PWM
Par.CF69 Condenser fan control signal of the circuit #2
0= 0 ÷ 10V
1= 4÷20mA
2= PWM
Par. FA01 Fan regulation
0 = Output not enabled
1 = always on
2 = ON/OFF step regulation
3 = ON/OFF continuous step regulation
4 = proportional fan speed
Par. FA02 Fan operative mode
0 = Fan on only if compressor on
1 = Independent from the compressor, off during the stand–by / or from remote OFF
Parameter combination FA01 – FA02
Par. FA01 = 1 + Par. FA02 = 0
Fans on when the compressor on (the fans work following the same output algorithm)
Par. FA01 = 1 + Par. FA02 = 1
Independent from the compressor status but off in stand–by.
Par. FA01 = 2 + Par. FA02 = 0
Fans on, with ON/OFF regulation and with temperature/pressure transducer control, only when the compressor is on (at least one relay
is configured as fan control). When the compressor turns off also the fans are forced off.
Par. FA01 = 2 + Par. FA02 = 1
Fans on, with ON/OFF regulation and with temperature/pressure transducer control, only when the compressor is on (at least one relay
is configured as fan control). When the compressor turns off the fans are thermoregulated depending on the condensing
temperature/pressure.
Par. FA01 = 3 + Par. FA02 = 0
Fans on, with ON/OFF continuos regulation and with temperature/pressure transducer control, only when the compressor is on (at least
one relay is configured as fan control). When the compressor turns off also the fans are forced off.
Par. FA01 = 3 + Par. FA02 = 1
Fans on, with ON/OFF continuos regulation and with temperature/pressure transducer control, only when the compressor is on (at least
one relay is configured as fan control). When the compressor turns off the fans are thermoregulated depending on the condensing
temperature/pressure.
Par. FA01 = 4 + Par. FA02 = 0
Fans on, with proportional regulation (PWM, 4..20mA, 0.10V) and with temperature/pressure transducer control, only when the
compressor is on. When the compressor turns off also the fans are forced off.
Par. FA01 = 4 + Par. FA02 = 2
Fans on, with proportional regulation (PWM, 4..20mA, 0.10V) and with temperature/pressure transducer control, only when the
compressor is on. When the compressor turns off the fans are thermoregulated depending on the condensing temperature/pressure.
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Comentarios a estos manuales
Relacionado con productos y manuales para Redes Emerson X-web300
Redes Emerson MONITORING OpenComms Manual de usuario
(48 paginas)
(48 paginas)
Redes Emerson OpenComms-485 Manual de usuario
(42 paginas)
(42 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(32 paginas)
(32 paginas)
Redes Emerson X-web500 Manual de usuario
(118 paginas)
(118 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(56 paginas)
(56 paginas)
Redes Emerson Liebert ICOM-DO Manual de usuario
(172 paginas)
(172 paginas)
(166 paginas)
Redes Emerson FM-3 Especificaciones
(110 paginas)
(110 paginas)
Redes Emerson FM-3 Manual de usuario
(8 paginas)
(8 paginas)
Redes Emerson Liebert ICOM-DO Manual de usuario
(12 paginas)
(12 paginas)
Redes Emerson Liebert CW Manual de usuario
(136 paginas)
(136 paginas)
Redes Emerson Liebert FPC Manual de usuario
(58 paginas)
(58 paginas)
Redes Emerson FM-3 Guía de usuario
(263 paginas)
(263 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med