Emerson X-web300 Manual de usuario Pagina 59
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
1592015300 User manual iCHILL 200 L GB r1.3 09/09/2005
20 AUXILIARY RELAYS
The auxiliary relays can be configured to manage two independent, from heat pump or chiller mode, output controls.
Each output can be managed with a dedicated temperature or pressure probe input ( NTC probe, 4..20mA or 0..5V transducers) or with
the common available temperature or pressure configurable inputs.
The probe selection is made with parameters uS02 for the circuit 1 and uS06 for the circuit 2.
The function is enabled when the parameter uS01 <>0 for the circuit 1 and the parameter uS05<>0 for the circuit 2 and at least one
output is configured as auxiliary output.
Par. uS01 configuration auxiliary relay 1.
Par. uS05 configuration auxiliary relay 2
Value and function
0 = Not enabled
1 = Function enabled, direct action, also during stand-by or remote off.
2 = Function enabled, direct action, only with unit running.
3 = Function enabled, inverse action, also during stand-by or remote off
4 = Function enabled, inverse action, only with unit running.
20.1 AUXILIARY RELAY WITH DIRECT ACTION
When:
PBr < set : relay ON.
Pbr > set + differential: relay OFF.
Set < PBr < set + differential: previous status.
PBr = NTC probe or transducer selected by the parameters uS02 / uS06
20.2 AUXILIARY RELAY WITH INVERSE ACTION
When:
PBr > set : relay ON.
Pbr < set - differential: relay OFF.
Set – differential < PBr < set: previous status.
PBr = NTC probe or transducer selected by the parameters uS02 / uS06
If:
PBr > SET: relay ON
Pbr < SET– differential: Relay OFF
Set – differential < of PBr < SET: previous state
PBr = NTC probe or transducer selected with uS02 / uS06 parameters
21 COMPRESSOR THERMOREGULATION
21.1 THERMOREGULATION PARAMETER DESCRIPTION
Par. ST01 Chiller Setpoint
It allows to set the chiller working temperature within the range ST02..ST03.
Par. ST02 Minimum setpoint limit in chiller.
The user can not program a setpoint value lower than ST02, the range is –30 °C..ST01.
Par. ST03 Maximum setpoint limit in chiller.
The user can not program a setpoint value higher than ST02, the range is ST01..70°C.
- DIXELL 1
- INDEX 2
- 4
- 1 GENERAL ADVICE 7
- 2 GENERAL FEATURES 8
- 2.1 MAIN FUNCTION 8
- Pg.10/106 10
- 4 USER INTERFACE 11
- Pg.12/106 12
- 4.4 KEY FUNCTION 14
- 4.5 KEY COMBINANTION 15
- 4.6 LED AND ICONS 15
- 4.7 DISPLAY AND ICONS 16
- 5 REMOTE TERMINAL 17
- 6 FIRST INSTALLING 17
- 6.2 RTC SETUP 17
- 7 WIRING CONNECTIONS 18
- 7.4 DIGITAL INPUTS 19
- Pg.20/106 20
- Pg.22/106 22
- 7.12 HOT KEY 64 CONNECTION 23
- 7.13 XJ485 CONNECTION 23
- Pg.24/106 24
- Pg.26/106 26
- 8.7 OTHER OUTPUTS 27
- 9 TABLE OF THE PARAMETERS 28
- Pg.30/106 30
- Pg.32/106 32
- Pg.34/106 34
- Pg.36/106 36
- Pg.38/106 38
- Pg.40/106 40
- Pg.42/106 42
- Enter the programming 42
- Pg.44/106 44
- Pg.46/106 46
- GRAPH: AUTOMATIC CHANGE OVER 46
- HOW THE CIRCUIT 1 OR 2 47
- 15 CUSTOM DISPLAY 48
- Pg.50/106 50
- HOW THE SET POINT VALUE 51
- ODIFY THE SET POINT 51
- 16.4 DISPLAY IN REMOTE OFF 52
- 17 FUNCTION MENU “ M” KEY 52
- 18 ENERGY SAVING 56
- 19 DYNAMIC SETPOINT 57
- 19.1 DYNAMIC SETPOINT GRAPH 58
- 20 AUXILIARY RELAYS 59
- Pg.60/106 60
- /RECOVERY 62
- 27 COMPRESSORS 64
- 27.1 COMPRESSORS START- UP 64
- 27.2 DIRECT START- UP 64
- 27.4 PART WINDING 65
- 27.7 STAR - DELTA START 65
- 28 CAPACITY CONTROL 66
- 28.1 MINIMUM LOAD START- UP 67
- 29 PUMP DOWN 68
- ACTIVATION 69
- UMP DOWN INFORMATION 70
- NLOADING DESCRIPTION 70
- NLOADING INFORMATION 70
- Pg.72/106 72
- FA26 Hot start differential 73
- 36 LOAD MAINTENANCE 74
- 37 CONDENSER FAN REGULATION 74
- OUTPUT FOR FAN CONTROL 75
- Pg.76/106 76
- 38 DEFROST CYCLE 77
- 38.1 FORCED DEFROST 77
- 38.2 COMBINED DEFROST 77
- 38.3 MANUAL DEFROST 78
- EFROST PARAMETER DESCRIPTION 79
- Pg.80/106 80
- 39 RECOVERY 81
- THE RECOVERY CYCLE 82
- 40.1 RECOVERY DISABLED 82
- AEFL evaporator flow alarm 83
- NOTE ABOUT THE FLOW ALARM 83
- 41.7 AEE EEPROM ALARM 84
- Significato label display 85
- 41.11 ARTF CLOCK FAILURE 86
- 41.12 ARTC CLOCK ALARM 87
- Pg.88/106 88
- Pg.90/106 90
- - PRESSURE SWITCH ALARM / 90
- Pg.92/106 92
- 41.38 ALARM RELAY AND BUZZER 94
- 41.39 KEYABOARD ALARM 94
- Pg.96/106 96
- Alarm description 96
- 44 BLACK-OUT 98
- 45 INSTALLING AND MOUNTING 98
- 45.1 PANEL CUT- OUT 98
- 45.4 METAL FRONT FRAME 99
- 46 ELECTRICAL CONNECTIONS 100
- 47 ACCESSORIES 100
- 47.3 TRANSFORMER 101
- 48 TECHNICAL DATA 102
Comentarios a estos manuales
Relacionado con productos y manuales para Redes Emerson X-web300
Redes Emerson MONITORING OpenComms Manual de usuario
(48 paginas)
(48 paginas)
Redes Emerson OpenComms-485 Manual de usuario
(42 paginas)
(42 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(32 paginas)
(32 paginas)
Redes Emerson X-web500 Manual de usuario
(118 paginas)
(118 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(56 paginas)
(56 paginas)
Redes Emerson Liebert ICOM-DO Manual de usuario
(172 paginas)
(172 paginas)
(166 paginas)
Redes Emerson FM-3 Especificaciones
(110 paginas)
(110 paginas)
Redes Emerson FM-3 Manual de usuario
(8 paginas)
(8 paginas)
Redes Emerson Liebert ICOM-DO Manual de usuario
(12 paginas)
(12 paginas)
Redes Emerson Liebert CW Manual de usuario
(136 paginas)
(136 paginas)
Redes Emerson Liebert FPC Manual de usuario
(58 paginas)
(58 paginas)
Redes Emerson FM-3 Guía de usuario
(263 paginas)
(263 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(88 paginas)
(88 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
urenrjrjkvnm
Med