Emerson MICRO MOTION 2700 Manual de instalación Pagina 205
- Pagina / 264
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Transmitter Configuration and Use: Series 1000 and 2000 Transmitters 195
Menu Flowcharts – Model 1700/2700 AN Transmitters continued
Model 1700/2700 IS Display CodesModel 2700 CIOModel 1700/2700 AN
Figure G-2 ProLink II configuration menu (continued)
Configuration
ProLink
Device
•Tag
•Date
• Descriptor
• Message
• Sensor type
• Floating pt ordering
• Add comm resp delay
• Transmitter serial #
Digital comm settings
• Digital comm fault
setting
• Modbus address
• HART address
• HART device ID
Burst setup
• Enable burst
•Burst CMD
•Burst var 1–4
Update rate
• Update rate
• 100 Hz variable
Frequency/Discrete
output
(1)
• Frequency
• Tertiary variable
• Scaling method
• Freq factor
(2)
• Rate factor
(2)
• Pulses per unit
(3)
• Units per pulse
(4)
• Freq pulse width
• Last measured value
timeout
• Freq fault action
• Freq output polarity
• Discrete output
• Assignment
• DO1 polarity
• Flow switch setpoint
Variable mapping
•PV is
•SV is
•TV is
•QV is
Display config
•mA 1
• Var 2 – Var 15
Display options
• Display start/stop
totalizers
• Display totalizer reset
• Dislay auto scroll
• Display offline menu
• Display offline
password
• Display alarm menu
• Display ack all alarms
• Offline password
• Auto scroll rate
RS-485
•Protocol
• Baud rate
•Parity
•Stop bits
Choose typical HART
settings
(1) The discrete output option is available only on Model 2700
transmitters.
(2) Displayed only if Scaling method is set to Frequency = flow.
(3) Displayed only if Scaling method is set to Pulses/unit.
(4) Displayed only if Scaling method is set to Units/pulse.
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Relacionado con productos y manuales para De medición, control y control Emerson MICRO MOTION 2700
(66 paginas)
(3 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales