Emerson MICRO MOTION 2700 Manual de instalación Pagina 175
- Pagina / 264
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Transmitter Configuration and Use: Series 1000 and 2000 Transmitters 165
Enhanced Density Model 2500 CIOModel 1500 ANCalibration
Appendix D
Configuring the Enhanced Density Application
D.1 About this chapter
This appendix describes the configuration procedure for the enhanced density
application.
Note: The enhanced density application is an optional feature of the Series 2000
transmitter, and may not be installed or enabled on your transmitter. To verify that it
is installed, connect to your transmitter using ProLink II, then click on
View/Installed Options.
D.2 Configuration overview
To configure and enable the enhanced density application, the following general steps are required.
1. If you have standard or custom curves (see Section D.3), you may need to load the curve file
onto your transmitter. Instructions are provided in Section D.5.1.
2. If you do not have standard or custom curves, you must configure one or more density curves.
For detailed instructions, see the ProLink II v2.1 manual, available on the Micro Motion web
site, or contact Micro Motion.
3. Specify the active curve. Instructions are provided in Section D.5.2.
4. Perform a density curve trim (optional). Instructions are provided in Section D.6.
Other actions that can be performed include:
• Modifying specific curve parameters (see Section D.7)
• Saving a curve to a file (see Section D.8)
D.3 Application options – Standard or custom curves
When the enhanced density application is purchased, a set of six standard curves may or may not be
supplied with the application. These curves are described in Table D-1. For information on obtaining
these curves, contact Micro Motion.
In addition, custom curves may be purchased. These curves are defined using customer-supplied data.
Custom curves can be installed at the factory, or the customer can load the purchased curve file(s) into
the transmitter using ProLink II.
CAUTION
Changing configuration can affect transmitter
operation.
Set control devices for manual operation before changing
transmitter configuration.
• Model 2500 CIO
• Model 2700 AN
• Model 2700 IS
• Model 2700 CIO
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Relacionado con productos y manuales para De medición, control y control Emerson MICRO MOTION 2700
(66 paginas)
(3 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales