Emerson Solu Comp Xmt-P-FF/FI Manual de instrucciones

Model Solu Comp®Xmt-CTwo-Wire Contacting Conductivity TransmitterInstruction ManualPN 51-Xmt-C/rev.BOctober 2005

2MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONS1.2 SPECIFICATIONS1.2.1 GENERAL SPECIFICATIONSCase: ABS. Pipe, surface, and panel mount version

MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONS31.2.2 FUNCTIONAL SPECIFICATIONSAutomatic Temperature Compensation: 3-wire Pt 100

4MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONS1.3 HAZARDOUS LOCATION APPROVALSIntrinsic Safety:Class I, II, III, Div. 1 Groups A-GT4 Tamb = 5

MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONSFIGURE 1-1. MENU TREE FOR MODEL SOLU COMP XMT-C-HT TRANSMITTER1.4 MENU TREE FOR MODEL XMT-C-HT5

MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONSFIGURE 1-2. MENU TREE FOR MODEL SOLU COMP XMT-C-FF TRANSMITTER1.5 MENU TREE FOR MODEL XMT-C-FF6

7MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONS1.7 FOUNDATION FIELDBUSFigure 1-3 shows a Xmt-C-FF being used to measure conductivity. The figu

8MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONSFIGURE 1-4. HART and FOUNDATION™ Fieldbus Communicators. Both the Rosemount Model 375 (or 275) a

MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONSFIGURE 1-5. AMS MAIN MENU TOOLS9

10MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONS1.10 ACCESSORIESPOWER SUPPLY: Use the Model 515 Power Supply to provide dc loop power to the t

11MODEL XMT-C SECTION 2.0INSTALLATIONSECTION 2.0INSTALLATION2.1 Unpacking and Inspection2.2 Installation2.1 UNPACKING AND INSPECTIONInspect the shippi

Emerson Process ManagementRosemount Analytical Inc.2400 Barranca ParkwayIrvine, CA 92606 USATel: (949) 757-8500Fax: (949) 474-7250http://www.raihome.

12MODEL XMT-C SECTION 2.0INSTALLATIONFIGURE 2-3. Panel Mount InstallationAccess to the wiring terminals is through the rear cover. Four screws hold th

13MODEL XMT-C SECTION 2.0INSTALLATIONFIGURE 2-4. Pipe Mount InstallationThe front panel is hinged at the bottom. The panel swings down for access to t

14MODEL XMT-C SECTION 2.0INSTALLATIONFIGURE 2-5. Surface Mount InstallationThe front panel is hinged at the bottom. The panel swings down for access t

15MODEL XMT-C SECTION 3.0 WIRING3.1 POWER SUPPLY/CURRENT LOOP — MODEL XMT-C-HT3.1.1 Power Supply and Load Requirements.Refer to Figure 3-1.The supply

16MODEL XMT-C SECTION 3.0 WIRING3.2 POWER SUPPLY WIRING FOR MODEL XMT-C-FF3.2.1 Power Supply Wiring. For general purpose areas,wire power as shown in

17MODEL XMT-C SECTION 3.0 WIRING3.3 SENSOR WIRINGKeep sensor wiring separate from power wiring. For best EMI/RFI protection, use shielded output sign

18For FM Intrinsically Safe Label, see Figure 4-1.For FM Intrinsically Safe Installation, see Figure 4-2.For CSA Instrinsically Safe Label, see Figure

19MODEL XMT-C SECTION 4.0INTRINSICALLY SAFE INSTALLATIONFIGURE 4-2. FM Intrinsically Safe Installation Wiring

MODEL XMT-C SECTION 4.0INTRINSICALLY SAFE INSTALLATIONFIGURE 4-3. CSA Intrinsically Safe Installation Label20

MODEL XMT-C SECTION 4.0INTRINSICALLY SAFE INSTALLATIONFIGURE 4-4. CSA Intrinsically Safe Installation Wiring21

QUICK START GUIDEFOR MODEL SOLU COMP Xmt-C TRANSMITTER5. Choose measurement: Conductivity, Resistivity, Total Dissoved Solids, orCustom. 6. Enter the

MODEL XMT-C SECTION 4.0INTRINSICALLY SAFE INSTALLATION22FIGURE 4-5. Baseefa/ATEX Intrinsically Safe Installation label

MODEL XMT-C SECTION 4.0INTRINSICALLY SAFE INSTALLATION23FIGURE 4-6. Baseefa/ATEX Intrinsically Safe Installation Wiring

24MODEL XMT-C SECTION 5.0 DISPLAY AND OPERATIONSECTION 5.0DISPLAY AND OPERATION5.1. DISPLAYThe Model Xmt-C has a two-line dis-play. Generally, the us

MODEL XMT-C SECTION 5.0 DISPLAY AND OPERATION5.3 PROGRAMMING AND CALIBRATING THE MODEL XMT- TUTORIALSetting up and calibrating the Model Xmt is easy.

26MODEL XMT-C SECTION 5.0 DISPLAY AND OPERATION5.4 MENU TREESThe Model Xmt-C-HT transmitter has four menus: CALIBRATE, PROGRAM, HOLD, and DISPLAY. Un

MODEL XMT-C SECTION 5.0 DISPLAY AND OPERATIONFIGURE 5-3. MENU TREE FOR MODEL SOLU COMP XMT-C-HT TRANSMITTER27

28MODEL XMT-C SECTION 5.0 DISPLAY AND OPERATIONFIGURE 5-4. MENU TREE FOR MODEL SOLU COMP XMT-C-FF TRANSMITTER

MODEL XMT-C SECTION 5.0 DISPLAY AND OPERATION1. If a security code has been programmed, pressing MENU causes the securi-ty screen to appear.2. Enter

30MODEL XMT-C SECTION 6.0 OPERATION WITH MODEL 375SECTION 6.0OPERATION WITH MODEL 3756.1 Note on Model 375 HART and Foundation Fieldbus CommunicatorTh

MODEL XMT-C SECTION 6.0 OPERATION WITH MODEL 3756.3 Operation6.3.1 Off-line and On-line OperationThe Model 375 Communicator features off-line and on-l

32MODEL XMT-C SECTION 6.0 OPERATION WITH MODEL 375Device setupProcess variablesCond *RawConductanceTempTemp resView statusDiag/ServiceTest deviceLoop

MODEL XMT-C SECTION 6.0 OPERATION WITH MODEL 375Detailed setupSensorsMain sensorPV Type [Conductivity, Resistivity, 0-12% NaOH, 0-15% HCl, 0-25% H2SO4

34MODEL XMT-C SECTION 6.0 OPERATION WITH MODEL 375HART outputPV is ProcessSV is TemperatureTV is Raw processPoll addrBurst option [PV, %range/current,

35MODEL XMT-C SECTION 7.0 CALIBRATION — TEMPERATURESECTION 7.0CALIBRATION — TEMPERATURE7.1 INTRODUCTIONThe Calibrate Menu allows the user to calibrate

36MODEL XMT-C SECTION 8.0 CALIBRATION — CONDUCTIVITYSECTION 8.0CALIBRATION — CONDUCTIVITYThe following procedures are described in this section:• En

37MODEL XMT-C SECTION 8.0 CALIBRATION — CONDUCTIVITY8.1 ENTERING THE CELL CONSTANTThe cell constant should be entered:• When the unit is installed fo

38MODEL XMT-C SECTION 8.0 CALIBRATION — CONDUCTIVITY8.2 ZEROING THE INSTRUMENTThis procedure is used to compensate for small offsets to the conductiv

39MODEL XMT-C SECTION 8.0 CALIBRATION — CONDUCTIVITY8.3 CALIBRATING THE SENSOR IN A CONDUCTIVITY STANDARDThis procedure is used to check and correct

40MODEL XMT-C SECTION 8.0 CALIBRATION — CONDUCTIVITY8.4 CALIBRATING THE SENSOR TO A LABORATORY INSTRUMENTThis procedure is used to check the and corr

41MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTERSECTION 9.0PROGRAMMING THE TRANSMITTER9.1 GENERALThis section describes how to program the transm

iMODEL XMT-C TABLE OF CONTENTSMODEL XMT-C TWO-WIRE CONDUCTIVITY TRANSMITTERTABLE OF CONTENTSSection Title Page1.0 DESCRIPTION AND SPECIFICATIONS ...

42MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTER9.3 CONFIGURING AND RANGING THE OUTPUT (-HT version only)9.3.1 Purpose1. Configuring an output m

43MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTER9.3.3 Procedure: Configuring the Output1. Press MENU. The menu screen appears. Choose Program.2.

44MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTERCurrent Outputfor Test:112.00mAOOuuttppuuttTempMeasurement >>TTeesstt OOuuttppuuttTrim Outp

45MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTER9.4 CHOOSING AND CONFIGURING THE ANALYTICAL MEASUREMENT9.4.1 PurposeThis section describes how to

MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTER469.5.3 Procedure: Temperature.To choose a menu item, move the cursor to the item and press ENTER.

47MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTEROutputs TempMeasurement>>>>SSeeccuurriittyyHARTReset Analyzer >>9.6.2 Procedure

48MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTER9.7 MAKING HART RELATED SETTINGSFor more information refer to Section 6.0.9.8 RESETTING FACTORY C

49MODEL XMT-C SECTION 9.0 PROGRAMMING THE TRANSMITTERDDeeffaauulltt DDiissppllaayyDisplay Contrast9.9.2 Procedure: Choosing a display screen.Calibrate

50MODEL Xmt-C SECTION 10.0MAINTENANCESECTION 10.0MAINTENANCEREPLACEMENT PARTS FOR SOLU COMP XMT (PANEL MOUNT VERSION)PART NUMBER DESCRIPTION SHIPPING

51MODEL XMT-C SECTION 11.0THEORY OF OPERATIONSECTION 11.0THEORY OF OPERATION11.1 CONDUCTIVITY / RESISTIVITY / % CONCENTRATIONLiquids can only conduc

MODEL XMT-C TABLE OF CONTENTSTABLE OF CONTENTS CONT’Dii9.0 PROGRAMMING THE TRANSMITTER...

52MODEL XMT-C SECTION 11.0THEORY OF OPERATIONDEFINITIONS1. LINEAR TEMPERATURE COEFFICENT OR TEMPERATURE SLOPE. The change in the conductivity of moste

12.1 OVERVIEW OF HART COMMUNICATIONHART (highway addressable remote transducer) is a digital communication system in which two frequencies aresuperimp

54MODEL XMT-C SECTION 12.0THEORY - REMOTE COMMUNICATIONS12.3 ASSET MANAGEMENT SOLUTIONSAsset Management Solutions (AMS) is software that helps plant p

MODEL XMT-C SECTION 13.0RETURN OF MATERIALSECTION 13.0RETURN OF MATERIAL13.1 GENERAL.To expedite the repair and return of instruments, propercommunica

WARRANTYGoods and part(s) (excluding consumables) manufactured by Seller are warranted to be free from defects in workman-ship and material under norm

Credit Cards for U.S. Purchases Only.The right people,the right answers,right now.ON-LINE ORDERING NOW AVAILABLE ON OUR WEB SITEhttp://www.raihome.com

MODEL XMT-C TABLE OF CONTENTSLIST OF FIGURESNumber Title Page1-1 Menu Tree — XMT-C-HT ...

1MODEL XMT-C SECTION 1.0DESCRIPTION AND SPECIFICATIONSSECTION 1.0DESCRIPTION AND SPECIFICATIONSModel Xmt™ Family of Two-wire Transmitters• CHOICE OF C