Emerson Network Router Manual de usuario Pagina 27
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation and Use Manual 21
Installation and Setup
ProLink II Setup Transmitter StartupUsing ProLink IIBefore You Begin
2.7 Obtain and configure a site key
To obtain and configure a site key:
1. Open the License Request file as follows:
Start > Programs > MMI > ProLink II v2.9 > ProLink II License Request Form
2. Edit the file, supplying all requested information including the site code.
To find the site code, choose
File > License (see Figure 2-13).
3. Save the edited file.
4. Contact Micro Motion in one of the following ways:
• Send an email to:
Flow.Support@Emerson.com
Attach the edited file to the email. The file is named LicenseRequest.txt, and in typical
installations is located in
Program Files > MMI > ProLink II v2.9.
Note: This is the default location. If the ProLink II installation program found an existing license file,
the program and License Request file were installed in the location of the license file.
• Telephone 800-522-6277 (toll-free in the U.S.), or 303-530-8250 (worldwide), and request
a site key. Have the edited registration text file available for reference.
Note: To minimize the possibility of error, Micro Motion recommends using the email method.
5. When the site key is provided:
a. Start ProLink II.
b. Choose
File > License. See Figure 2-13.
Table 2-6 Default communication parameters for RFT97xx and IFT97xx transmitters
Default values
Transmitter Physical layer Protocol Baud Data bits
(1)
(1) ProLink II automatically sets data bits appropriately for the configured protocol. Even though a data bits parameter may be
configured in the transmitter, you do not need to configure it in ProLink II.
Stop bits Parity Address
IFT9701/9703
(2)
(2) IFT9701/9703 communication parameters are not configurable. The settings shown here are always in effect.
Bell 202
(3)
(3) Connection to primary mA output.
HART 1200 8 1 odd 0
RFT9712 Bell 202
(3)
HART 1200 8 1 odd 0
RS-485
(4)
(4) Connection to RS-485 terminals.
HART 1200 8 1 odd 0
RFT9739 v2 Bell 202
(3)
HART 1200 8 1 odd 0
RS-485
(4)
HART 1200 8 1 odd 0
RFT9739 v3 Bell 202
(3)
HART 1200 8 1 odd 0
RS-485
(4)(5)
(5) Dip switch settings on the transmitter are used to select either Std. comm or User defined.
• Std. comm Modbus RTU 9600 8 1 odd 1
• User defined HART 1200 8 1 odd 0
- II Software 1
- Transmitters 1
- The Micro 2
- Contents 3
- Chapter 1 7
- Before You Begin 10
- 6 ProLink 12
- II Software for Micro Motion 12
- Transmitters 12
- Chapter 2 13
- Installation and Setup 13
- Terminals for connection type 16
- PV+ PV– A B A B A B 16
- Transmitter 16
- 2.5.1 Connection diagrams 17
- 12 ProLink 18
- HART/Bell 202 connections 20
- Parameter Option 25
- 20 ProLink 26
- OK as required by the 28
- Chapter 3 31
- Using ProLink II Software 31
- 26 ProLink 32
- Connection > Disconnect 34
- Tools > 34
- Commissioning Wizard 34
- 30 ProLink 36
- 32 ProLink 38
- 34 ProLink 40
- 36 ProLink 42
- Chapter 4 43
- 40 ProLink 46
- 42 ProLink 48
- Chapter 5 49
- 44 ProLink 50
- 46 ProLink 52
- Parameter ProLink II location 53
- Sensor type 53
- T- Se ri es O t h e r 53
- Newer tag Older tag 54
- Flow FCF X.XXXX FT X.XX 55
- 50 ProLink 56
- 5.5.3 Temperature calibration 60
- 56 ProLink 62
- 58 ProLink 64
- Chapter 6 65
- Meter Verification 65
- 60 ProLink 66
- Chapter 7 67
- Data Logger 67
- 62 ProLink 68
- 64 ProLink 70
- Appendix A 71
- 66 ProLink 72
- 68 ProLink 74
- 70 ProLink 76
- Figure A-10 Core processor 77
- 72 ProLink 78
- Appendix B 79
- 74 ProLink 80
- Flow source Description 82
- Setting Default Description 82
- 78 ProLink 84
- 80 ProLink 86
- Figure B-3 Discrete Input tab 87
- Function 88
- Default 88
- 84 ProLink 90
- Index Discrete Batch 91
- 86 ProLink 92
- 88 ProLink 94
- *20001909* 96
Relacionado con productos y manuales para Hardware Emerson Network Router
Hardware Emerson SiteI/O 32/0 Manual de usuario
(5 paginas)
(5 paginas)
Hardware Emerson PrPMC800 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Emerson SiteI/O-Line Manual de usuario
(6 paginas)
(6 paginas)
Hardware Emerson 00825-0100-4075 Manual de usuario
(28 paginas)
(28 paginas)
Hardware Emerson 400518-01 Manual de usuario
(88 paginas)
(88 paginas)
Hardware Emerson SiteLink-12 Manual de usuario
(5 paginas)
(5 paginas)
Hardware Emerson SITETPI-E V3 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Emerson OpenComms-485 Manual de usuario
(39 paginas)
(39 paginas)
Hardware Emerson Network Power Manual de usuario
(4 paginas)
(4 paginas)
Hardware Emerson SiteLink-12E Manual de usuario
(24 paginas)
(24 paginas)
Hardware Emerson Liebert CW Manual de usuario
(28 paginas)
(28 paginas)
Hardware Emerson Liebert XDP-W Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales