Emerson LMS 1000 Manual de instalación descargar pdf (Pagina 145)

NetSure™ LMS Data Processing Unit

Installation Instructions, Section 5879 (Issue BA, April 7, 2014)

Spec. No: 58650500, 586505500 Code: Section 5879

Model No: LMS1000 Issue BA, April 7, 2014

[137 of 149]

CONFIG R_

Note:

If "Y" was entered above, the

system responds with...

System Alarm Report mode (Y or

N):

Type

if the system is required to initiate an alarm report via phone

lines if this channel alarms and

if not, then press

ENTER

Note:

If "Y" was entered above for "Alarm

Type", the system responds with...

Alarm Class Number:

Type the desired alarm class number associated with this channel, then

press

ENTER

. Alarm classes are specified with the numbers 0 through 8,

with 0 representing no alarm class.

Note:

This parameter is configurable only

if the channel is configured as an

Alarm Type.

Condition Type:

This parameter applies only to TL1 commands/messages. Type the

name (20 characters maximum) which describes this alarm or event

state, then press

ENTER

. Only alpha characters can be entered for this

parameter. TL1 uses specific values for this parameter. Refer to

TA-NWT-001360 Tables 5-1 through 5-4.

Note:

This parameter is configurable only

if the channel is configured as an

Alarm Type.

Condition Description:

This parameter applies only to TL1 commands/messages. Type a user-

defined text message (40 characters maximum) which provides a

detailed description of this alarm, event, or condition. Then press

ENTER

. May also be used to describe any action to be taken as a result

of the condition. All printable ASCII characters are valid except for the

percent sign (%), double quotes ("), and the backslash (\).

Note:

This parameter is configurable only

if the channel is configured as an

Alarm Type.

Notification Code:

This parameter applies only to TL1 commands/messages. Type one of

the following codes which describes the severity of this alarm or event

condition, then press

ENTER

CR - critical alarm

MJ - major alarm

MN - minor alarm

NA - not alarmed

NR - not reported when event occurs

Note:

This parameter is configurable only

if the channel is configured as an

Alarm Type.

Service Effect Code:

This parameter applies only to TL1 commands/messages. Type one of

the following codes which describes how this alarm or event affects

service, then press

ENTER

SA=service-affecting condition, immediate action required

NSA=nonservice-affecting condition, action required

Affected by ACO (Y or N):

Type the characters

which represent if the alarm can be cut off,

then press

ENTER

. Y=yes, ACO enabled, N=NO, ACO disabled

Cycle Freq (min):

Type the required cycle frequency of the relay channel (0-1440

minutes), then press

ENTER

. When a relay is energized, the system can

be programmed to de-energize the relay at a selected time interval.

This time interval is determined by the relay’s "cycle frequency". This

feature resets external alarm logic that requires an open to close

transition for alarming. During a relay alarm condition, the relay

remains energized for the time duration determined by the value of

the relay’s cycle frequency. Once this time period expires, the system

de-energizes the relay for 15 seconds. The system will then

re-energize the relay if the alarm condition still exists.

If the relay channel is set to be affected by ACO, the cycle frequency is

also used to automatically release the alarm cut-off feature at a

selected time interval determined by the cycle frequency. The system

automatically performs the equivalent of a CLR ACO command at the

end of the "cycle frequency". To disable these features, set the "cycle

frequency" to zero.

1 2 ... 140 141 142 143 144 145 146 147 148 149 150 ... 157 158

Comentarios a estos manuales

Sin comentarios

Emerson LMS 1000 Manual de instalación Pagina 145

Comentarios a estos manuales

Relacionado con productos y manuales para No Emerson LMS 1000