Emerson 644 Especificaciones Pagina 44
- Pagina / 182
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
34
Reference Manual
00809-0200-4728, Rev RA
Section 2: Configuration
April 2015
Configuration
2.10 Configure measurement filtering
2.10.1 50/60 Hz filter
The 50/60 Hz Filter (also known as Line Voltage Filter or AC Power Filter) function sets the
transmitter electronic filter to reject the frequency of the AC power supply in the plant. The 60
Hz or 50 Hz mode can be chosen. The factory default for this setting is 50 Hz.
Configuring 50/60 Hz filter with a Field Communicator
From the HOME screen, enter the Fast Key sequence.
Configuring 50/60 Hz filter with AMS Device Manager
1. Right click on the device and select Configure.
2. In the left navigation pane select Manual Setup.
3. On the Device Tab there will be a group box called Noise Rejection, in the box AC
Power Filter select from the drop down menu.
4. Select Apply when complete.
2.10.2 Resetting the device
Processor Reset function resets the electronics without actually powering down the unit. It
does not return the transmitter to the original factory configuration.
Performing a processor reset with a Field Communicator
From the HOME screen, enter the Fast Key sequence.
Performing a processor reset AMS Device Manager
1. Right click on the device and select Service Tools.
2. In the left navigation pane select Maintenance.
3. On the Reset/Restore Tab select the Processor Reset button.
4. Select Apply when complete.
2.10.3 Intermittent Sensor Detection
The Intermittent Sensor Detection feature (also known as the transient filter) is designed to
guard against erratic process temperature readings caused by intermittent open sensor
conditions. An intermittent sensor condition is an open sensor condition that lasts less than one
update. By default, the transmitter is shipped with the intermittent sensor detection feature
switched ON and the threshold value set at 0.2% of sensor limits. The intermittent sensor detect
Device Dashboard Fast Keys
2, 2, 7, 4, 1
Device Dashboard Fast Keys
3, 4, 6, 1
- Protocol 1
- Rosemount 644 3
- Temperature Transmitter 3
- Title Page 4
- Contents 5
- 6Section 6: Troubleshooting 8
- Reference Manual 10
- Table of Contents 10
- Section 1 Introduction 11
- 1.2 Overview 12
- 1.2.2 Transmitter overview 13
- 1.3 Considerations 14
- 1.4 Return of materials 15
- 1.5 Transmitter security 16
- Section 2 Configuration 17
- 2.3 System readiness 18
- 2.4 Configuration methods 19
- Configuring with an LOI 21
- 2.4.4 Failure mode 22
- 2.5 Verify configuration 23
- 2, 2, 8, 6 26
- 2.6.3 Setting output units 28
- Setting output units with LOI 29
- Communicator 30
- 2, 2, 3, 3 31
- Resetting Hot Backup 33
- 2.8 Configure device outputs 35
- 2.8.2 Damping 36
- 2, 2, 1, 5 2, 2, 1, 6 38
- Configuring tag with LOI 43
- 2.10.1 50/60 Hz filter 44
- 2.10.2 Resetting the device 44
- 2.11 Diagnostics and service 46
- 2, 2, 4, 3, 4 48
- AMS terms 49
- Configure min/max with LOI 50
- Special considerations 53
- Hot Backup 53
- 3.1 Overview 55
- 3.2 Safety messages 55
- 3.3 Considerations 56
- 3.4 Installation procedures 57
- 3.4.1 Set the alarm switch 58
- 3.4.2 Mount the transmitter 59
- 3.4.3 Install the device 60
- 4.1 Overview 67
- 4.2 Safety messages 67
- 4.3.1 Sensor connections 69
- 4.3.2 Power the transmitter 70
- 4.3.3 Ground the transmitter 71
- Shielding recommendations 72
- Option 2 73
- Option 3 73
- Grounded thermocouple inputs 74
- (HART/4–20 75
- Electrical Installation 76
- Figure 4-4. Load Limits 76
- 5.1 Overview 77
- 5.2 Safety messages 77
- 5.3 Calibration overview 78
- 5.4 Sensor input trim 79
- 3, 4, 4, 1 80
- 3, 4, 4, 2 81
- 5.5 Trim the analog output 82
- 3, 4, 5, 1 83
- 3, 4, 5, 2 83
- 5.7 Switching HART Revision 86
- Section 6 Troubleshooting 87
- 6.4 Diagnostic messages 90
- (SIS) Certification 93
- 7.4 Commissioning 94
- 7.5 Configuration 95
- 7.7.1 Proof test 96
- 7.7.2 Partial proof test 96
- 7.8 Specifications 98
- 7.8.3 Product life 99
- A.1 Specifications 101
- A.1.2 Physical 102
- OUNDATION 103
- A.1.3 Performance 104
- Sensor connections 105
- Communication requirements 106
- Power supply 107
- Temperature limits 107
- Turn-on time 108
- External transient protection 108
- Accuracy 108
- Accuracy example 110
- OUNDATION fieldbus 111
- 644H (DIN A Head Mount) 113
- 644 Field Mount 114
- 644 Rail Mount 114
- Sanitary Applications 117
- A.4 Ordering information 118
- 00809-0200-4728, Rev RA 123
- April 2015 123
- 2 NPT 00644-4438-0002 126
- 2 NPT 00644-4438-0102 126
- 2 NPT 00644-4438-0004 126
- 2 NPT 00644-4438-0104 126
- A.4.1 Configuration 127
- A.4.2 Tagging 127
- A.4.3 Considerations 127
- Custom configuration 128
- Head Mount 129
- A.5.2 Physical specifications 130
- Enclosure ratings (644H) 131
- Sanitary housing surface 131
- Load limitations 133
- Configuration 135
- ≤ Ta ≤ +85°C); Type 4X; 137
- 2-14 NPT) enclosure 137
- International 140
- Gas -40 °C ≤ Ta ≤ +65 °C 142
- Dust -40 °C ≤ Ta ≤ +85 °C 142
- T5 -40 °C ≤ Ta ≤ +70 °C 145
- T6 -60 °C ≤ Ta ≤ +40 °C 145
- T5 -60 °C ≤ Ta ≤ +85 °C 145
- Combinations 146
- Additional Certifications 147
- Product Certifications 149
- Sheet 2 of 2 158
- Trees and Fast Keys 165
- D.1 Number entry 173
- D.2 Text entry 174
- 175
- Canceling 176
- D.5 LOI menu tree 177
Relacionado con productos y manuales para De medición, control y control Emerson 644
(92 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales