Emerson CH Breaker Gateway Especificaciones Pagina 52
- Pagina / 252
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-6 • E2 RX/BX/CX I&O Manual 026-1610 Rev 10 06-APR-2010
and replace it with an identical 3.6V battery obtained from
or approved by Retail Solutions. DO NOT USE AA BAT-
TERIES IN THIS BATTERY SLOT.
After replacing the battery, you must tell E2 the battery
has been replaced so it can reset its battery life counter.
1. Log in to E2 (level 4 password or higher).
2. Press
, followed by --- to
navigate to the System Tests screen.
3. Move the cursor to the Replace Battery field.
Press
for Yes, then press .
4. Make sure the new battery is in place, and
press
.
If successful, the battery icon should disappear from
the top of the screen. If it is still there, check for proper
battery placement, verify the battery enable switch posi-
tion, and repeat this procedure.
- 026-1610 Rev 10 06-APR-2010 1
- Table of Contents 5
- 1Introduction 15
- 1.3 The E2 Convenience 16
- Store Controller 16
- 1.4 Networking Overview 17
- Echelon Box-To-Box 18
- Ethernet Box-To-Box 18
- 1.5 Documentation Over 19
- 1.6 On-Line Help System 20
- Overview 20
- 1.7 Software Licensing 20
- 2 Hardware Overview 21
- - E2 PIB 22
- - E2 Keyboard 22
- - PIB LED’s Status 22
- 2.2 I/O Network Boards 23
- 2.2.2 MultiFlex Boards 24
- Output Boards 25
- 2.2.2.3 MultiFlex CUB 27
- (RCB) (BX and CX Only) 27
- 2.2.2.6 MultiFlex PAK Board 27
- 2.2.3 The MultiFlex ESR Board 28
- 814-3110) 28
- - 8RO Relay Output Board 29
- - 8ROSMT Relay Output Board 29
- 2.2.6 4AO Analog Output Board 30
- 2.3 Echelon Network 31
- Boards and Peripherals 31
- 2.3.5 The ESR8 (Discontinued) 32
- 2.3.6 TD3 Temperature Display 33
- 3 Mounting 35
- 3.1.3 Retrofit Mounting 36
- 3.2 Mounting I/O Boards 37
- (Snap Track) 38
- 3.3.1 16AIe and 8ROe 38
- 3.3.3 ESR8 (Discontinued) 39
- 3.3.4 MultiFlex ESR 39
- 3.3.5 TD3 39
- 3.4.2 Two-Channel and Four 40
- Channel Repeaters 40
- 3.5.1 Pressure Transducers 41
- 3.5.2.2 Mounting 42
- 3.5.3.1 Location 42
- 3.5.3.2 Mounting 42
- 3.5.4.1 Location 42
- 3.5.4.2 Mounting 42
- 3.5.6.1 Location 43
- 3.5.8.1 Indoor RH Sensor 43
- 3.5.8.2 Outdoor RH Sensors 44
- 3.5.9 Dewpoint Probe 45
- 3.5.10 Light Level Sensor 45
- 3.5.11 Liquid Level Sensors 45
- 4 E2 Hardware Setup 47
- 4.2 Powering the E2 48
- 4.3 Add-On E2 Peripherals 48
- Mounting 49
- 4.3.4.1 LEDs 50
- 4.3.5.1 LEDs 50
- 4.4 Battery Testing and 51
- Replacement 51
- --- to 52
- for Yes, then press 52
- RS485 I/O or MODBUS Net 53
- 5 Serial Configura 55
- E2 PIB COM PORT ASSOCIATIONS 56
- 6.1 The I/O Network 57
- 6.1.2.1 Board Designation 58
- 6.1.2.2 Board Calculations 58
- X + (Y • 8) < 256 58
- Numbers) 59
- 6.1.7 Setting the Baud Rate 59
- Biasing Jumpers 60
- 6.1.9 Powering the I/O Boards 60
- 6.2 Lennox IMC Rooftop 61
- Unit Controllers 61
- 6.3 Control Techniques 62
- Drive (VSD) 62
- 6.4 ECT MODBUS 62
- INSTALLATION GUIDE 64
- 4-20 OUT 65
- 120/208/240 VAC 67
- 16AI INSTALLATION GUIDE 68
- RS485 I/O NET 69
- 7.1 Ethernet IP Configura 71
- 7.2 Hardware Specifica 71
- 7.3 Software Specifica 72
- 7.4 Ethernet Network 72
- 7.5 Software Setup 73
- 7.6 Troubleshooting 74
- 8.1 Overview 75
- 8.2 Wiring Type 75
- 8.3 Echelon Network 75
- Structuring (Daisy-Chains) 75
- 8.4 Device Termination 76
- 8.5 Wire Restrictions 77
- 8.6 Installing Echelon 77
- 8.7 LEDs 78
- 8.8 Open Echelon Device 78
- Connectivity 78
- (Network Setup) 79
- 8.8.1.1 Troubleshooting 79
- Valve #4 81
- 9 Input and Output Setup 83
- 9.1.2 Power Connection 84
- WALL-MOUNT 86
- DEWPOINT SENSOR 86
- BACK PLATE 86
- (FRONT VIEW) 86
- (Input Definitions) 88
- - Data Type Pop-Up Menu 89
- (potentiometer) 91
- 9.2 The 8RO, 8IO, and 92
- MultiFlex Outputs 92
- 9.2.4 Relay Output Test Mode 93
- (Output Definitions) 94
- Status Screen 95
- - Digital Output Screen 96
- - Analog Output Screen 97
- 9.3 CC-100 Case Control 98
- 9.3.2 Power Module Wiring 99
- 9.3.3 Valve Cable 99
- 9.4 CCB Case Controllers 100
- 9.5 ESR8 and MultiFlex 100
- ESR Valve Output Wiring 100
- 10 Quick Start 103
- 10.3 Setting Number of 104
- Network Devices 104
- 10.5 The Main Status 105
- (Home) Screen 105
- 10.4 Setting Number of 105
- Applications 105
- 10.6 Common Screen Ele 106
- 10.7 Screen Types 107
- (Setup). The actual setup 108
- (System Configuration) 109
- (System Information) 110
- 10.8 Time/Date Setup 111
- 10.9 Set Up Modem 112
- 10.10 Set Up TCP/IP 113
- 10.11 Set Up Network Baud 114
- 10.12 Set Up User Access 115
- if you are 116
- 10.13 Set Up I/O Network 117
- 10.14 Set Up Echelon Net 118
- (Network Setup) 119
- (Network Summary) 119
- (DISCONTINUED) 120
- 10.15 License Management 121
- (Licensing) 122
- 10.16 Set Up Alarming 123
- (General Controller Info) 124
- (Alarm Setup) 125
- (Dial-out Setup) 125
- 10.17 Set Up Global Data 126
- 10.18 Set Up Applications 127
- to add an application 128
- (Delete Application) 128
- to open the Actions 129
- and 129
- Property Help 130
- 11 Software Overview 131
- 11.1.4 Hardware Overview 132
- 11.2 Condenser Control 133
- 11.2.2 Evaporative Condensers 134
- 11.2.3 Fan Control 134
- 11.2.4 Condenser Split Mode 134
- 11.2.5 Fast Recovery 134
- 11.2.6 Hardware Overview 134
- 11.3 Standard Circuits 135
- 11.3.2 Defrost Control 136
- 11.4 Case Control Circuits 140
- 11.4.3 Refrigeration Control 141
- 11.4.4 Defrost Control 142
- 11.4.5 Anti-Sweat Control 143
- 11.4.6 Dual Temp Control 144
- 11.4.7 Fan Control 144
- 11.4.8 Light Control 144
- 11.4.9 Clean/Wash Mode 144
- 11.4.11 Fail-Safe Mode 145
- 11.5 Logging Groups 146
- System Configuration 147
- Logging Setup 147
- 11.5.4 Logging Group Status 148
- 11.5.5 Log Reports 148
- for System Configuration 149
- Display Logged Points 149
- 11.6 Air Handling Units 150
- 11.6.5 Economizer Control 151
- 11.6.9 Curtailment 152
- 11.6.11 Separate Setpoints 153
- 11.6.12 AHU Zone Control 153
- 11.6.13 Hardware Overview 153
- 11.7 Zone Control 154
- 11.7.2 How Zones Work 155
- Connected To Zones 155
- 11.7.4 Temperature Control 156
- 11.7.5 Zone Temperature 156
- 11.7.6 Economizer Control 156
- 11.7.7 Economization Enable 156
- 11.7.11.2 AHUs 157
- the Network Setup menu 158
- for Associations 158
- 11.8 MultiFlex CUB Board 159
- 11.9 MultiFlex PAK Board 159
- 11.10 Lighting Schedules 159
- 11.10.3 Control Method Select 160
- 11.10.4 Standard Control 160
- 11.10.5 Alternate Control 161
- 11.10.7 The Min ON/OFF Cell 162
- 11.10.8 The Proof Cell 162
- 11.11 Demand Control 163
- 11.11.3 Load Shedding 164
- 11.11.4 Shedding Levels 164
- 11.11.5 Priority Levels 164
- - Shedding Priority Levels 165
- Load Shedding 166
- 11.12 Sensor Control 167
- 11.13 Loop/Sequence Con 168
- Descriptions 169
- 11.14 Time Scheduling and 171
- Holidays 171
- 11.15 Power Monitoring 172
- 11.15.2 Logging 173
- 11.16 Anti-Sweat Setup 174
- 11.17 Heat/Cool Control 174
- 11.17.4 Setpoint Reset 175
- 11.18 Analog and Digital 176
- Combiners 176
- 11.19 TD Control 177
- 11.20 Pulse Accumulation 178
- 11.21 Irrigation Control 179
- 11.21.3 Cycle Scheduling 180
- 11.21.4 Zone Inhibit 180
- 11.21.5 Zone Bypass Inputs 180
- 11.21.5.1 Bypass Failsafe 181
- 11.21.6.1 Leak Test 181
- 11.22 Flexible Combiner 182
- 12.1 The E2 Home Screen 185
- 12.2 Logging On and 186
- Access Levels 186
- 12.3 Toggling Full Options 187
- 12.4 Navigation 187
- 12.4.2 Screen Types 189
- . This will take you to 189
- 12.4.3 The E2 Keypad 190
- key moves the 191
- 12.5 Customizing the 192
- Home Screen 192
- 12.6 Manual Defrost and 192
- Clean Mode 192
- 12.7 Overrides 193
- 12.8 Checking Boards 194
- 12.9 Checking Status 194
- 12.10 Alarms 195
- 12.10.8.1 Acknowledging 196
- 12.10.8.2 Resetting 197
- 12.10.8.3 Clearing 197
- 12.11 Viewing Logs and 198
- 12.11.2 Log View 200
- to open the Actions Menu 200
- 12.11.3 The Graph View 200
- 12.11.4 Zooming In and Out 200
- 12.12 Low Battery Notifica 201
- Alarm Name 208
- Default 208
- Priority 208
- Definition 208
- P Proportional Mode 221
- I Integral Mode 221
- D Derivative Mode 221
- Integral Mode 222
- “P” + “I” MODES 223
- How Condenser Control and 224
- HVAC PID Differs From The 224
- Other PID Features 225
- Minimum Accumulated Error 226
- Filtering 226
- Limits and Precision Table 229
- Appendix F: Troubleshooting 231
- . Highlight the Point 238
Relacionado con productos y manuales para Gateways / Controladores Emerson CH Breaker Gateway
Gateways / Controladores Emerson 1410 Manual de servicio
(222 paginas)
(222 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales