Emerson ROC364 Manual de instrucciones

Part Number D301144X012Field Automation SystemsROC364 I/O CARDInstruction Manual SupplementForm A6097May 2000

ROC364 Instruction Manual 6-6 Rev 5/006.4.2 Analog Output ChannelsAnalog outputs (AOs) provide a current output for powering analog devices. The ROC3

ROC364 Instruction Manual Rev 5/00 6-7The discrete inputs provided on the I/O Card are configured as Point Number A1 to Point Number A12.They are conn

ROC364 Instruction Manual 6-8 Rev 5/00+-SELF-POWEREDDISCRETE DEVICEDOC4005A-R326.4.4 Discrete Output ChannelsThe discrete output channels are normally

ROC364 Instruction Manual Rev 5/00 6-9 + Positive Pulse Input (Sourced) - CommonTo wire a pulse input channel (shown in Figure Section: 6-8), conn

ROC364 Instruction Manual 6-10 Rev 5/006.5 TROUBLESHOOTING AND REPAIRIf multiple I/O channels do not appear to be working, check the STATUS LED on the

ROC364 Instruction Manual Rev 5/00 6-116.5.1 Analog Input ChannelsEquipment Required: MultimeterTo determine if an Analog Input channel is operating p

ROC364 Instruction Manual 6-12 Rev 5/006.5.2 Analog Output ChannelsThe Analog Output channel is used for current loop devices. Use the following proc

ROC364 Instruction Manual Rev 5/00 6-136.5.4 Discrete Output ChannelsEquipment Required: MultimeterPersonal Computer running ROCLINK SoftwarePlace the

ROC364 Instruction Manual 6-14 Rev 5/006.6 REPLACEMENT PROCEDURE6.6.1 Impact on I/O Point ConfigurationWhen an I/O Card is replaced with another I/O C

ROC364 Instruction Manual Rev 5/00 6-15CAUTIONFailure to exercise proper electrostatic discharge precautions (such as wearing agrounded wrist strap) m

ROC364 I/O Card ii Rev 5/00Revision Tracking SheetMay 2000This manual may be revised from time to time to incorporate new or updated information. The

ROC364 Instruction Manual 6-16 Rev 5/00 6.7 I/O CARD SPECIFICATIONSSpecificationsPOWERInput: Uses 0.57 W (supplied by MCU), excludingpower consumed

ROC364 I/O Card Rev 5/00 iiiAbout this SupplementThis document, Form A6097, contains supplemental pages for the ROC364 Remote OperationsController Ins

ROC364 I/O Card iv Rev 5/00[This page is intentionally left blank.]

ROC364 Instruction Manual Rev 5/00 6-1Section: 6. — ROC364 I/O Card6.1 SCOPEThis section describes the 32-point Input/Output (I/O) Card used with the

ROC364 Instruction Manual 6-2 Rev 5/00The ROC364 I/O Card provides these I/O channels:♦ 12 Discrete Inputs – DIs.♦ 4 Pulse Inputs – PIs.♦ 8 Analog Inp

ROC364 Instruction Manual Rev 5/00 6-36.3 INITIAL INSTALLATION AND SETUPIf the I/O Card is not already installed onto a ROC364 MCU, use may use the f

ROC364 Instruction Manual 6-4 Rev 5/006.4 CONNECTING THE I/O CHANNELS TO WIRINGEach I/O channel on the I/O Card is electrically connected to field wi

ROC364 Instruction Manual Rev 5/00 6-5+T+-Current Limit+-T+-ROC-POWEREDCURRENT LOOPDEVICE+T = 12/24 VDC, 22 mA max.+SIGNAL = 4 TO 20 mA250 OHMAIDOC009