Emerson Avocent Universal Management Gateway Guía de usuario Pagina 19
- Pagina / 146
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation.....13
2. Use a UTP crossover cable to connect the devices to the appliance, using an adaptor, if
necessary.
NOTE: To comply with EMC requirements, use shielded cables for all port connections.
WARNING: Do not turn on the power on the connected devices until after the appliance is turned on.
To daisy chain PDUs to the appliance:
NOTE: This procedure assumes you have one PDU connected to a port on the appliance.
1. Connect one end of a UTP cable with RJ-45 connectors to the OUT port of the connected
PDU.
2. Connect the other end of the cable to the IN port of the chained PDU. Repeat both steps until
you have connected the desired number of PDUs.
NOTE: For performance reasons,do not connect more than 128 outlets per serial port.
See Port configuration on page 50 for more information on how to set up serial targets.
KVM
If your appliance supports KVM connections, use a UTP cable and a UMIQmodule to connect a
KVMtarget to an autosensing port on the appliance.
- Installer/User Guide 1
- TABLE OF CONTENTS 3
- Table of Contents.....iii 5
- Product Overview 7
- Network and serial mode 8
- Web user interface (UI) 9
- VGA and USB connections 9
- CLI setup port 9
- IPv4 and IPv6 support 10
- Security 10
- Power management 10
- Auto discovery 10
- Flexible users and groups 11
- Installation 13
- Wall mounting 14
- Installation.....9 15
- Connecting the Hardware 17
- Connecting targets 18
- Installation.....13 19
- Turning On the Appliance 20
- Verifying the Connections 20
- Configuring the Appliance 21
- Configuration Example 22
- Descriptions 23
- Installation.....19 25
- Initial Appliance Setup 27
- Setting Up Your Network 28
- Firewall 29
- Port requirements 30
- Trellis™ 32
- Trellis™ platform 32
- Web User Interface 33
- Using the Sidebar 34
- Admin role 35
- Operator role 35
- User role 35
- Administration 36
- Defaults 38
- Network Settings 39
- Bridge Group Configuration 40
- OSPF and BGP 43
- Network Share 45
- User role group 45
- Password Policy 46
- Preemption Levels 46
- Adding a user 47
- Authentication 48
- Administration.....43 49
- User Target Access 50
- User Target Rights 50
- Managing user groups 51
- Appliance Administrator group 51
- Power User group 52
- User group 52
- Group Target Access 52
- Group Target Rights 53
- Manage Target Settings 54
- View Logs 54
- Administration.....49 55
- Licenses 56
- Port configuration 56
- Port assignment 57
- Serial Settings 58
- DHCP Settings 59
- Advanced settings 60
- Discovery 60
- Physical discovery 60
- Logical discovery 62
- Administration.....57 63
- Generic service processors 64
- Discovery log 65
- SPmanagement 66
- Default Users 67
- Access settings 67
- Serial management 68
- Serial console ports 69
- Data Buffering 70
- 0 with severity info 70
- Data logging 71
- Serial PDUports 71
- Serial rack PDU 71
- PDUmanagement 72
- Network PDU 73
- SNMPSettings 73
- Serial PDUs 74
- Asset Location 75
- UMIQ module 76
- Module settings 79
- Active sessions 80
- Default settings 80
- Administration.....75 81
- • AES - AES encryption 82
- Default Settings 83
- Target groups 85
- Firmware 86
- Backing up firmware 87
- USBDevices 88
- Com Digital Input 89
- Digital inputs 90
- Environment 90
- RS-485environment sensor 91
- PDU Temperature Sensors Delta 91
- Monitoring 92
- Digital Output 93
- Firewall and NAT 96
- Administration - Targets 97
- Defined networks 98
- Administration.....93 99
- Network - Hosts 101
- Add to add a new host 101
- Firewall and NAT - Hosts 101
- Services 102
- Administration.....97 103
- NATflow 105
- Firewall flow 106
- Firewall and NATflow 106
- NATsetup 108
- Firewall setup 109
- Number Description 111
- 1 Sidebar 111
- 2 Targets Table 111
- Service Processors 112
- Sessions 113
- Appliance 114
- Sessions tab 114
- Power capping 115
- UMIQ Modules 116
- KVM session optimization 116
- Targets.....111 117
- Serial Console 118
- Overview 119
- Settings 119
- Power Outlet 121
- Sensors and Events 123
- CPU and disk usage 124
- Appendices 125
- Appendices.....123 129
- Netboot Recovery 130
- #as the 131
- 0 for this parameter 131
- LAN performance 133
- WAN performance 133
- Bridge groups 134
- Hardware 134
- Network related 135
- Firewall and NAT on page 90 137
- Firewall and NAT 138
- Appendices.....133 139
- Apply when done 140
- /usr/bin/restartsnmpsvr 141
- Appendix L:Video Resolution 142
- Appendices.....137 143
- Technical Support Site 145
- About Emerson Network Power 146
Relacionado con productos y manuales para Redes Emerson Avocent Universal Management Gateway
Redes Emerson 5500 Series Manual de usuario
(43 paginas)
(43 paginas)
Redes Emerson FM-3 Manual de instalación
(230 paginas)
(230 paginas)
Redes Emerson FM-3 Guía para resolver problemas
(60 paginas)
(60 paginas)
Redes Emerson MVME55006E Manual de servicio
(54 paginas)
(54 paginas)
Redes Emerson Liebert ICOM-DO Manual de instalación
(88 paginas)
(88 paginas)
Redes Emerson Liebert CW Manual de usuario
(88 paginas)
(88 paginas)
Redes Emerson FM-3 Manual de instalación
(60 paginas)
(60 paginas)
Redes Emerson 1420 Manual de usuario
(12 paginas)
(12 paginas)
Redes Emerson Liebert FPC Manual de usuario
(16 paginas)
(16 paginas)
Redes Emerson Liebert FPC Manual de usuario
(44 paginas)
(44 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(73 paginas)
(73 paginas)
Redes Emerson X-web300 Manual de usuario
(102 paginas)
(102 paginas)
Redes Emerson MONITORING OpenComms Manual de usuario
(48 paginas)
(48 paginas)
Redes Emerson OpenComms-485 Manual de usuario
(42 paginas)
(42 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales