Emerson Liebert Static Transfer Switch Instrucciones de operaciones Pagina 141
- Pagina / 150
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Event Message Help Text 129
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type
CA and press RETURN on your keyboard.
OUTPUT UV
Output Undervoltage
The voltage being supplied to the load has dropped below the acceptable nominal voltage. Check the input voltage
from both sources.
This event and the system status surrounding it have been written to a History Log if the History Logs were not already
full. This event was also written to the Event Log, if so configured.
Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the STS2
system from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.
The alarm has triggered a message to be sent to the modem, if so configured.
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type
CA and press RETURN on your keyboard.
INPUT CONTACT #1
Input Contact Isolator #1
Occurrence of the indicated external event has been detected by Input Contact Isolator #1 of the Open Comms Digital
Input option board.
Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the STS2
system from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.
The event, with its assigned name, was written to the Event Log, if so configured.
The alarm has triggered a message to be sent to the modem, if so configured.
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type
CA and press RETURN on your keyboard.
INPUT CONTACT #2
Input Contact Isolator #2
Occurrence of the indicated external event has been detected by Input Contact Isolator #2 of the Open Comms Digital
Input option board.
Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the STS2
system from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.
The event, with its assigned name, was written to the Event Log, if so configured.
The alarm has triggered a message to be sent to the modem, if so configured.
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type
CA and press RETURN on your keyboard.
INPUT CONTACT #3
Input Contact Isolator #3
Occurrence of the indicated external event has been detected by Input Contact Isolator #3 of the Open Comms Digital
Input option board.
- Static Transfer Switch 2 1
- 2
- Table of Contents 3
- List of Figures 9
- List of Tables 11
- IMPORTANT SAFETY INSTRUCTIONS 13
- OVERVIEW OF MANUAL 14
- SUPPORT INFORMATION 15
- 6 18
- 1.0 SAFETY PRECAUTIONS 19
- 2.0 UNPACKING AND INSPECTIONS 20
- 2.3 Internal Inspections 21
- 3.0 LOCATION CONSIDERATIONS 22
- 3.4 Altitude 23
- Max. Ambient Temperature 23
- Altitude—Feet 23
- 4.0 LOCATING THE STS2 24
- 5.0 POWER AND CONTROL WIRING 25
- 5.3 System Grounding 27
- 5.6 Power Supply 29
- 6.0 OPTIONS 30
- 6.3 Comms Board 31
- 6.4 Internal Modem 31
- 6.6 Remote Source Selection 32
- 6.7 Key Lockout Switch 32
- 6.8 Redundant Output Breaker 32
- 6.10 Seismic Floor Anchors 33
- 22 Options 34
- 7.0 INSTALLATION DRAWINGS 35
- FRONT VIEW SIDE VIEW 36
- BOTTOM VIEW TOP VIEW 36
- DETAIL A 36
- FRONT VIEW 37
- SIDE VIEW 37
- TOP VIEWBOTTOM VIEW 37
- TOP VIEW 38
- BOTTOM VIEW 38
- FILE NAME: 41
- FIGURE 2 43
- FIGURE 3 43
- SECTION A-A 44
- ONE-LINE DIAGRAM 44
- COLUMBUS, OHIO 43229 50
- 1050 DEARBORN DRIVE 50
- PROGRAMMABLE RELAY BOARD 54
- TABLE (J51) 55
- NETWORK INTERFACE 58
- CARD (NIC) 416241GX 58
- CONTROL WIRING 59
- RS-232 INTERFACE 59
- STATIC TRANSFER SWITCH 2 59
- OUTLINE DRAWING 60
- INPUT JUNCTION BOX 60
- 8.1 System Description 63
- 8.2 Modes of Operation 64
- 8.3 Operator Controls 65
- 9.0 THEORY OF OPERATION 66
- Hardware 68
- Firmware 68
- 9.2.2 Circuit Breakers 68
- 9.2.4 Logic Modules 69
- 9.2.5 Audible Alarm 69
- 9.2.6 RS-232 Port 69
- 9.2.3 SCRs 69
- 10.1 Normal System Turn-On 70
- 10.4 Maintenance Bypass 73
- 10.5 Normal System Shutdown 76
- 11.0 ALARM AND FAULTS 77
- 11.2 Event and History Logs 78
- 11.3 Alarm Notes 79
- 11.4 List of Messages 79
- Table 9 Event Messages 80
- 12.0 COMMUNICATION INTERFACES 82
- Groups Parameter 84
- Item Parameter 84
- Value Parameter 85
- 13.1 Display Overview 91
- 13.2 Menu Overview 92
- 13.2.1 Security 93
- Using the Password 93
- 13.3 Mimic Display 94
- 13.4 Event Controls 94
- 13.5 Event Display 94
- 13.6 Menu bar 94
- User Settings 95
- Source Set Points 96
- System Settings 99
- Comm Options 99
- Configuring the Modem 100
- STS2 Touch Screen Display 89 101
- Configuring Pager Support 102
- STS2 Touch Screen Display 91 103
- SiteScan Configuration 105
- System Options 105
- Event Log 107
- History Log 107
- System ID 107
- 13.6.2 Logs 107
- 13.6.3 Source Transfers 108
- 13.6.4 Startup Procedure 108
- 13.6.5 Bypass Procedure 108
- 13.6.6 Help 109
- 13.6.7 Logo 109
- PERATING THE LED DISPLAY STS2 111
- 14.1.2 Event Controls 112
- 14.1.3 LED Definitions 113
- 14.1.4 Button Definitions 114
- 14.1.5 Key Lockout Switch 114
- 14.2 Operations 115
- 14.2.3 Maintenance Bypass 116
- 14.2.4 Normal System Shutdown 118
- 15.0 SPECIFICATIONS 119
- 15.1.4 Grounding 120
- 15.1.7 Response Time 120
- 15.2 System Components 121
- 15.2.4 Access 122
- 15.2.5 Circuit Breakers 122
- 15.2.6 Cable Entrance 122
- 15.2.7 Doors 122
- 15.2.9 RS-232 Port 123
- 15.2.12 Maintenance Bypass 124
- 15.2.13 Fuseless Design 124
- 15.2.14 Options 124
- 16.0 EVENT MESSAGE HELP TEXT 125
- 17.0 MAINTENANCE 147
- 17.4 Contacting Liebert 148
- 6WDWLF7UDQVIHU6ZLWFK 150
Relacionado con productos y manuales para Los conmutadores de red Emerson Liebert Static Transfer Switch
(52 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales